Welcome to B2BAGE
1 - 10 Results for

Other Physical Measuring Instruments

Found 130 Products
Cast Iron straight edge

Cast Iron straight edge

Jan 06, 2013
Used for machine maintenance, inspection and irregularity and not straight twoface is in line with the block Specifications :200-8000 (both light and heavy)Uses: Used for machine maintenance, inspection and irregularity and not...
Cast Iron V-Block

Cast Iron V-Block

Jan 06, 2013
Cast Iron V-Block is used to test various shaft concentricity and contour for a precision bearing class crossed Cast Iron V-Block is used to test various...
Granite parallels

Granite parallels

Jan 06, 2013
For inspecting the parallelism of work-pieces also for replacing the working blocks at the same height when reqired          Flatness of working surface&parallelism of opposite surfaceSquareness between Working surfacesTolerance of h.w...
Granite straightedges

Granite straightedges

Jan 06, 2013
For inspecting the straightness and flatness          straightness&flatness of working surfaceparallelism between Working surfacessquareness between Working surface and side...
NJC61 Nonmetal Ultrasonic detector

NJC61 Nonmetal Ultrasonic detector

Jan 07, 2013
Purpose ²        Testing building foundation piles by crosshole ultrasonic wave method. ²        Inspecting concrete defects by ultrasonic method, such as uncompacted place, cellular hole area ²        Detecting concrete...
NJ-20 mortar test hammer

NJ-20 mortar test hammer

Jan 07, 2013
Brief introduction:   This instrument is specially used in testing the compressive strength of mortar in building brick component.       Trait:   1) Center rod use imported materials, high precision, wear proof.   2) Shell made from super hard aluminum, perfectly protect instrument from damage on site work,...
NJ-225 concrete test hammer

NJ-225 concrete test hammer

Jan 07, 2013
Brief introduction:   The test hammer submits to standard of GB/T9138-1988 and JJG817-93 and JGJ/T23-2001. NJ-225 concrete test hammer is applied to test the compressive strength of building concrete components, bridge and so on.       Trait:   1)Center rod is made from imported material, high accuracy and...
Multi-finger Caliper Tools or MFC Tools 24/40/60

Multi-finger Caliper Tools or MFC Tools 24/40/60

Jun 16, 2015
1. Composition Multi-Finger caliper tool is composed of electronics assembly, Multi-finger assembly,Caliper measuring assembly, Motor assembly. 2. Function The primary function of Multi-Finger Caliper is to detect the deformation, bending, fracture, perforation and inside corrosion of tubing or casing with multi caliper fingers that are in...
Engine oil apparent viscosity analyzer CCS

Engine oil apparent viscosity analyzer CCS

May 19, 2015
Scope of application The apparent viscosity of the engine oil analyzer applicable standards: GB/T6538 ASTM D5293 The instrument is mainly the test cryogenic engine oil dynamic viscosity index using The advanced technology of The contemporary set of mechanical, optical, electronic and computer technology in one temperature measurement,...
Automatic kinematic viscosity tester for petroleum products

Automatic kinematic viscosity tester for petroleum products

May 19, 2015
Scope of application The instrument is designed and made as per GB/T265-88, ISO3104, ASTMD445, IP71 prescribed requirements, Test the kinematic viscosity or liquid oil products, ie, Newtonian liquid. in units of m2 / s, mm2 / s are usually used in practice. The dynamic viscosity is the kinematic viscosity of The liquid measured at a...
Ads by Google



About Us | Contact Us | Help | Terms & Conditions
Hot Products: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 0-9
Copyright Notice @ 2008-2013 B2BAGE Limited and/or its subsidiaries and licensors. All rights reserved.