LOWEST FALSE ALARM,HIGH TECHNOLOGY,HIGH CHIP TO PROTECTION MOTION ROOM,PET IMMUNE OPTIONAL,OUTDOOR PIR OPTIONAL,WORK WITH ALARMS

PRODUCT INTRODUCTION

       The product is wireless passive infrared detector with high stability. It has adopted advanced technology in signal processing and provided superhigh detection ability and anti error alarm. The detector will detect movement of human automatically when intruder pass through the detected area, and it will send out alarm signal to alarm host if there is movement. The product is suitable for the safety of residential house, villas, factories, markets, warehouses, office building etc.

MAIN FEATURE

ASIC Adopted 

Auto temperature compensation

Send alarm signal by RF

Adjustable detecting distance

Low battery indication

SMT design adopted

TECHNICAL SPECIFICATION

   Operating voltage:DC9(Battery NO. “6F22”)

     Static current: ≤25uA

     Alarm current: ≤15mA

     Detecting distance: 10m

     Detecting angle: 110°  (2~4° optional)

     Code  form: 2262 or 1527

     Radio frequency: 315MHz  or 433.92MHz

     Radio distance: 200m (open area)

     Low battery indicator: yellow LED

Alarm indicator: red LED

     Sensor: dual element infrared sensor  

     Operating temperature: -10°C ~ +50°C

     Environment humidity: ≤ 95% RH (nocongelation)

     Anti RF interference: 10MHz-1GHz  20V/m

     Installation mode: wall mounted or hanged in corner

     Installation height: 1.7 to 2.5m (2.2m is Proposed)

     Outline Size: 59L*39.5W*107H mm

INSTALLATION

1.   Installation at the outdoor. place with pets, air-condition nearby, direct sunshine, heat source and under the rotating objects  should  be  avoided.

2.    Surface of installation should be firm with no vibration.

3.    Installing the detector in the place where intruder pass  easily.

4.    Fixing bracket on the wall by screw.

5.    Hang the detector, it will work normally after turning on the power switch.

OPERATING INSTRUCTION

 Function  Setting

  1. Delay Jumper: used to set alarm delay time.When set to Test Mode(27 seconds), it will be triggered every 27 seconds when it has been triggered, while set to Work Mode (5minutes), it will be triggered every 5 minutes when it has been triggered.

    Short 1&2: delay 27s (test mode)

       Short 2&3: delay 5 minutes (work mode)

  2. Code Jumper: According to the alarm host,used to set address code and zone code with alarm host. A0-A7 is address code, which should correspond with alarm host. (No need for 1527 code IC ) D0-D3 is data code for setting defence zone. H=1, L=2, Empty =0.   NOTE:if the alarm host program to login detectors without playing jumpers. Please follow different alarm host to login detectors.

  3. LED: for setting LED ON without effect of  the detector work.

Short 1&2: set LED ON

4. Yellow LED:  Low battery indicator, when the LED on, please charge  the batteries in time.

Product testing

Turning on power and LED indicator will flashed for 1s, the detector comes into state of self-check, it takes about 30s, after that it is in the state of normal work. Conner should walk parallel with the wall installed detector in the testing area. LED lighting means the detector is in the state of alarm.

NOTICE

 1. Please install and  use the detector according to this manual, don't touch the surface of sensor for avoiding affecting the sensitivity of the detector. Please shut off  power and then clean the sensor by soft cloth with little alcohol  if cleaning needed.

 2. The product can reduce accident but may not perform as expected. The user is advised to take all necessary   precautions for his/her safety and the protection of his/her property.

 3. In order to ensure it can work normally, the power should be kept to supply and get on walking test periodically, once a week is better.