3G Video Alarm with PIR & SD,2000K pixels digit camera ,PIR detector ,IR for night use ,Video phone ,16 zone wireless detectors
3G Video Alarm with PIR & SD
1)2000K pixels digit camera
2)PIR detector
3)IR for night use
4)Video phone function
5)Support SD card Record
6)GPS function
7)Video upto QVGA(320×240)
8)Image upto UXGA(1600×1200)
9)16 zone wireless detectors
10) Alarm to 5 groups phone
11) Alarm to 1 group monitor center
12) Alarm to 1 group SMS center
13) Alarm to fix IP Address
14) Alarm to 2 groups Email
15) Interval time to reporting
16) Fixed time of arm and disarm
17) Built-in WCDMA/HSDPA/GSM/GPRS/EDGE
18) Built-in lithium battery
How to use it:
1)Open the battery cover ,put SIM cart in it, Inserts the SD card(FAT16) into the base, put the power 5V/2A DC into the base , put down switch of the base to open power supply.The LED turns to red and last for 20, and it will start to search 3G network. After 20 seconds, the LED is flashing in orange and the alarm system begins to read the information of the SIM memory. It will enter into the status of disarm and LED is go still green. It will be turned to be green and flashing in the status of alarm when you use controller to set the base in alarm. The LED is red and flashing when the base is in alarming.
2)you can send the message to setup the base .The format:password #operation code # content #
123456#11#1#; set the base alarm ; LED green and flashing in the base
123456#31#99998888#1#1#0# , set phone 99998888 and sent out message and picture when alarm.
123456#1#1#; get one video clips ( about 5 second) by your mobiphone if MMS setting is ok
123456#21# CMWAP# # # 10.0.0.172#9201# http:/mms.monternet.com #
Shus as MMS setting show in CHINA( other country will be different):
Access Point Name(APN): CMWAP ;Set GPRS Access point.
Username: (empty) ;Set MMS Uesr name.
Password: (empty) ;Set MMS Uesr Password.
Gateway IP (proxy) address(IP): 10.0.0.172 ;Set IP Address.
Port : 9201 ; Set Port
MMS (Relay) Server URL: http:/mms.monternet.com ;Set MMS Homepage.
Com Function
1#-# 1#( 1-5)#;ask video clips by your mobiphone; 1*, * stand for approves
2#-# 2#1# ,open siren,2#0# ,close siren
5#-# Output 3 minutes when alarm.but can set high when 5#1#,and low when 5#0#
11#-# 11#1# (Arm) ;11#0# (Disarm)*; set the base alarm or disalarm
12#-# 12#(arm time 0000-2359)#(disarm time 0000-2359)# ; set arm time-gap or disarm time-gap
14#-# 14#( video clips 1-5)# ; sent video clips to your mobiphone when alarm ,1*
15#-# 15#1#; PIR work*; 15#0# ;PIR no work; set PIR detector work or nowork
18#-# Change password (16 bit). 18#(1-6)#; 123456*
19#-# 19#1# ;Set CHINESE version * ; 19#0#; Set ENGLISH version
20## Show MMS setup in the base; 20##
21#-# MMS seting : 21# APN# USER# PASS# IP# PORT# MMSHomepage#
30## show preset phone number and status in the base; 30##
(31-35)#-# (31-35)# phone number # SMS (0,1)#MMS(0,1)# call(0,1)# video phone(0,1)#; 0--disable; 1--able32#99997777#0#0#0#1#,show only dialt video phone 99997777 when alarm.
40#-# Show mail address in the base 40##
41#-# Set First E^mail address(031bit) ; 41#269999--163,com#
42#-# Set Second E^mail address(031bit)
50#-# Show monitoring center phone number. 50##
51#-# 51# (center phone )#( user ID)# (arm or disarm report)# (1-- report0-- no report )
52#-# arm or disarm report center numbers: 52# arm report number# disarm report number #
53#-# Set netware IP Address 53#( IP)# (PORT)# (user ID)#
54#-# Set SMS center number. 54# (mobiphone number) # (user ID)#
55#-# Set time interval reporting :55# (center number 0-15bit)#( Time interval 1-99hour)# (Type 0-2)# Type: 0---send SMS;1---send MMS;2--- send SMS + MMS
70#-# Show wireless detector status (1-16) 70# (1-16)#
(71-86)#-# (71-86)#( 1-2 )# (SMS-24 bit)# ; (0--disarm,1--arm,2--24hours arm)71#1# front door PIR alarm# ; show first detector can arm and send message (front door PIR alarm)
How to add more detectors?
You can add new detector, such as wireless door sensors, PIR Sensors, gas and smoke detectors when you push the reset key(inside the battery cover) untill the LED change from green to red. You should trigger every detector, and the red LED will flash and shows successful .After you finish doing it,you can push the reset key again or waitting 20 seconds, it ends and automatically enter into working state.(with green LED),you can program it by 71# --86#
How to cancel the lost detector?
It often happens that some of coded detectors are lost. you can cancel the coded information of this detector so that it can not control your alarm system. just reset the alarm system by keeping reset key and turn on power and then beep or LED flashes, it shows reset is successful. All registered detector have been deleted and password is123456. You can register them again with the above solution.
How to control the base with remote controllers?
When you press, alarm, the LED of the base will be turned green with flashing. It shows the base is in arming status, it will alarm and dial out when you remove the door sensor, switch PIR Sensor, go across from the front of camera and so on. The LED will turn to red with flashing when the base is alarm.When you press, disalarm, the LED of the base will turn green and does not flash. It wont alarm and dial out. When you press Emergency help, it will alarm and send MMS and SMS or dial out no matter it is under arming status or disarming status. The LED will be red with flashing.
