Welcome to B2BAGE
JC Series Electronic Counter
JC Series Electronic Counter

Minimum Order: 0
Quality/Safety Certification: 0.00


1.High accurate
2.Credibility and permanence
3.Manufacture
Min order: 5 pieces

>>Overview 

 

JC Series Electroinc Counter is a high accurate counter, which adopts the single chip micro-processor with excellent performances as its main control component. Is has the advantages of high accuracy, wide counting range, digital display, soft-contact key operating, permanent data retention when power cut, strong anti-disturbance capability, pretty apprarance, etc.

 

Counter can be used in the industries of packing, printing, pharmacy, food, papermaking, ceramic, petroleum, chemical engineering, metallurgy, etc. operating for counting and display. It can also display and control the rotating revolution, lenth and other parameters.

 

 

>>Features

Adopting the microcomputer as its main control component in design. It is considered to replace hardware with software if possible, so that the reliability of the meter is improved obiviously.Adopting the E2PROM to hold the data in credibility and permanence.Adopting the optimized design with electromagnetism compatibility, so the anti-disturbance capability is strong.

 

>>Specifications

ModelRange of countingFunctionOutput power supplyAppearance size (mm)Size of mounting hole(H*W)Inserted depth(mm)
JC24S0-999999with pre-setting, counting freqency, counting  kind             12VDC/20mA24*48*6222.5*4558
JC20S0-999999counting output kind12VDC/20mA36*76*10033*73100(84)
JC48S0-9999output mono-stable time delay12VDC/30mA48*48*8545*4578
JC72S0-999999keeping data/not keeping data12VDC/30mA72*72*7568*6865
JC80S0-999999when power cut12VDC/60mA80*160*8076*15265

 

 

>>Technical parameters and Functions

Mounting kindpanel  mounting kind or socket mounting kind 
Selecting of counting kind

(1)When the counting value increases to its set point,contact output is produced and counting keeps on.

(2)When the counting value increases to its set value,contact output is produced and counting closes off.

(3)When counting value increases to its set-value, counting keeps on and the meter clears to zero automatically during its contact output with a mono-stable delay.

(4)When counting value increases to its set-value , counting closes off and the meter clears to zero automatically during its contact output with a mono-stable delay.

Contact capability  of the control output3A/250VAC (for resistance load) 
Keeping data/not keeping data is selected when power cut data retention time>10 years 
Counting frequencyhigh speed is 5000 times/s, low speed is 250 times/s (signal duty ratio is 1:1)
Input signals and the frequency that ought to be selected

(1)Contact signal:For delay,distance switch,microswitch,the frequency  should be selected in low speed(30 times/s)

(2)Non-contact signal:For approach switch, photoelectric switch, etc. the frequency can be selected in either high(1000 times/s) or low(30 times/s) according to requirement.

(3)Pulse signal:For TTL circuit and so  forth(low level VL=0-1.3V, high level VH=4.5-30V). the frequency can select  either high(1000 times/s) or low(30 times/s) according to requirement.

The input impedance of signal≥5kΩ
Reset(clear to zero) kind

The values of display and control output all reset at same

(1)Reset with the reset(clear to zero)key on the surface panel(only for the counting statue)

(2)Reset with the terminals wiring(make short of the RST and COM pins)

(3)Local automatic reset with mono-stable delay:0.1-9.9s is selectable (for JC80-Z, this function is without)

Power supply

220VAC (+10%,-15%) 50HZ+2%;(special  order is required for 24VDC or other voltage)
Power consumption≤4.5VA
Operating environmenttemperature 0-50°c ,relative humidity≤85%

Ads by Google



About Us | Contact Us | Help | Terms & Conditions
Hot Products: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 0-9
Copyright Notice @ 2008-2022 B2BAGE Limited and/or its subsidiaries and licensors. All rights reserved.