Rotary drum dryer:
1.High Cost Performance dryer
2.Low cost rotary dryer
3.Easy structure
4.Dryer capacity:2.5~36t/h
The rotary drum dryer
The introduction of rotary drier:
Rotary drum drier is a drying device, widely used in mining equipment.It can be divided into two categories,direct and indirect heat transfer drum dryers.
The main internal structure of rotary drier:
In order to increase the material evenly distributed in the rotor parts of the cross section in good contact with the drying medium, in the cylinder body installation raise plates.There are several characteristics of the rotary dryer.
1.It can be used to dry the fresh material from moisture content 65% to below 13% after the High temperature drying, disinfection, decomposition.
2.Drying product
3.Rotary Drum dryer has a high degree of mechanization, large production capacity and continuous operation.
4.Structure was simple and excellent. Materials running smoothly through the cylinder’s resistance.The operating are convenient.
5.Low malfunction, lower maintenance cost, low power consumption.
6.Wide scope of application, good uniformity of drying products .When it is drying at the same time can achieve the purpose of sterilization and deodorization.
Rotary dryer’s operating principle:
Dry and wet material from the belt conveyor or bucket elevator to the hopper,
then by feeding machine of hopper through charging pipe into the feed side. Feeding pipeline’s slope than the natural material, in order to materials smoothly into dry containers.Drier with the horizontal cylinder is a slightly into tilted rotating cylinder. Material from high end to join, heat body by low-end enter, with material into counter-current contact, also have heat body and materials together and flow into the barrel. with the cylinder rotate by gravity materials to a run on the bottom of the end. Wet materials in the cylinder body forward movement process, directly or indirectly got heat body heat, make wet materials to dry, then the discharge end by the belt conveyor or screw conveyor sent. In the cylinder body wall with copy plate, It is the function of the material copied up and planted,make the material and the airflow contact surface increases to improve the drying rate and to promote material progress. Heat-carrier is generally divided into hot air and flue gas. After the heat-carrier by the dryer, generally need the cyclone to trap the material of the gas down. through the bag filter or wet dust collector and then put emissions,if you want to reduce dust content of exhaust gas.
Technical parameters of rotarydryer
|
Specific-ations(m) | Capacity(t/h) | Main motor | Main gear box | Weight(t) | ||
Power(kw) | Model | Model | Speed reduction ratio | |||
Ø1.2*10 | 2.5 | 7.5 | Y160M-R3 | ZL50-16-I | ----- | 13.5 |
Ø1.5*12 | 3.3-4.9 | 10 | Y160L-6-B3 | JZQ500-III-2F | ----- | 18.9 |
Ø1.5*15 | 4-6 | 18.5 | Y200L1-6 | JZQ500-III-2F | ----- | 21 |
Ø1.8*12 | 4-6 | 18.5 | Y160L-6 | ZQ50-16II-2 | 16.46 | 22.83 |
Ø2.2*12 | 7-12 | 18.5 | Y200L7-6 | JZQ650-III | 31.5 | 37.6 |
Ø2.2*14 | 7-12 | 22 | Y200L7-6 | JZQ650-III | 31.5 | 40 |
Ø2.2*16 | 12 | 30 | Y225M-6 | JZQ750-III | 31.5 | 45 |
Ø2.4*14 | 12 | 30 | Y250M-6 | JZQ750-III | 31.5 | 51 |
Ø2.4*18 | 10-13 | 37 | Y250M-6 | ZL85-13-I | 27.16 | 54 |
Ø2.4*20 | 10-14 | 37 | Y250N-6 | ZL85-13-I | 27.16 | 54.14 |
Ø3*20 | 25 | 55 | Y250M-4 | ZL100-16-I | 41.52 | 78 |
Ø3*25 | 32-36 | 75 | YR280M-4 | ZL100-16-I | 41.52 | 104.9 |