Welcome to B2BAGE
SOLDERING STATION IRON TOOL SOLDER WELDING 60W ESD 936
SOLDERING STATION IRON TOOL SOLDER WELDING 60W ESD 936

Minimum Order: 0
Quality/Safety Certification: 0.00


soldering station 936 ESD 60W
1) Good quality & price
2) accept Paypal
3) Power input: 110V
4) Power Output: 24V 60W

SOLDERING STATION IRON TOOL SOLDER WELDING 60W ESD 936:

 

 operating instructions
- 200 °C temperature control knob to the position.
- A good soldering iron and connect the console.
- Connect the power.
- Turn on the switch, power indicator LED is lit.
- Temperature control knob to apply the temperature position.
- The proper temperature.
Too low temperature will slow the flow of solder, solder temperature is too high will burn the flux in the thick white to dry up, resulting in Weld or burn the circuit board. When the solder tip temperature in accordance with the needs of the correct settings, there is a good weld can be sure of. Commonly used in the electronics industry is 60% tin solder alloys, 40% lead (60/40). Tip of the soldering temperature according to the appropriate manufacturer vary, it is listed below:
Melting point: 215 °C
General temperature: 270 ~ 320 °C
Assembly line temperature: 320 ~ 380 °C
Note: The general use should not exceed 420 °C. If you need to use a higher temperature, short-term use is allowed.


 

the temperature adjustment
- The need for regular calibration temperature soldering iron, use the tip as the other models, the temperature is different, the need to correct temperature.
- Panel on the "CAL" hole in the chassis for external use by customers to make their own fine tuning screwdriver.

Tip the reasons for non-stick tin
- Tip temperature above 450 °C.
- To be used in the soldering tip surface did not give proper plus tin.
- In welding, in addition to tin, repair, welding and other operations in the lack of flux.
- Tip of the high sulfur content or dry sponge and rag and wipe.
- Exposure to organic materials such as plastic, silicon (Si) quality oil and other chemicals.
- Use of non-pure and low tin content solder.

Tip replacement and handling
Loosen the sleeve tip to remove the replacement. Temperature control units power must be turned off, and let cool before tip off tip, remove the sleeve fixed premises in the formation of oxide dust. Care must be taken to avoid this dust into the eyes. Replace tip and the power of a normal hand lock sleeve.

Replacement of iron core, should iron out of stainless steel tube core 23mm, within the iron core and then locking the handle mounting screws
Note: You must be careful not to over tighten, otherwise it will damage the heating element.

Maintenance
In order to ensure good function to the normal operation of soldering iron temperature control, please note the following recommendations. (If the soldering iron temperature control units, or some factors are not functioning properly, please contact the nearest service office support services).
General clean-up
- Iron grip or temperature control units can cover with a cloth dipped a small amount of liquid detergent cleaning.
- Do not immersed in the fluid temperature control units or allow liquids into the shell.
- Do not use any cleaning solvent shell.

The new tip
- Replace the tip line or use the 900M selected imported 936 tip.
- Iron grip or temperature control units can cover with a cloth dipped a small amount of liquid detergent cleaning.

the temperature control knob to set the low position. Turn on the power "switch."
heat reaches 300 °C, the surface of the tip soldering flux increases with tin wire.
continuous heating at 300 °C after five minutes, then set the temperature control knob go to the appropriate temperature location.
reach the appropriate temperature, to get started.
Note: When at any time using the new tip, the tip is best able to take out every day and clean up the internal foreign body!


Other motherboard repair tools we can offer:

 

 

 

Ads by Google



About Us | Contact Us | Help | Terms & Conditions
Hot Products: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 0-9
Copyright Notice @ 2008-2022 B2BAGE Limited and/or its subsidiaries and licensors. All rights reserved.