1.E1 PCM fiber optical mux equipment
2.64 audio and data
3.DI (drop/insert) function
4.support hot swap
5.FXS, HOT, MAG
FT-50S(3U) PCM fiber optical mux equipment is a 3U high standalonemultiplexer over fiber link, built upon a highly flexible. Main Features | |
Super Flexible Configuration
| -Can be configured as PDH fiber/electrical integrator, 64E1 2048×2048 non-blocking cross-connect channel PCM equipment or D/I device -Completely modular design -Up to 64 audio and data channels, multiple sub-channel cards include: FXS, FXO, hotline, magneto phone, 2100Hz carrier phone, 2 wire E/M, 4 wire E/M, telegraph, V.35, V.24/V.28, 64K, N×64K, Ethernet sub-channel card. E1 port can be 75Ohm or 120Ohm -Providing external clock input. |
High Intelligence and Powerful Network Management System
| -Can be configured in star or tree network according to users requirements -Up to 4 NMS platforms can run simultaneously in the same network, and the NMS platform can be deployed in any node of the network. -Operating status of local or remote devices can be detected and displayed through NMS. -Convenient to set cross-connect mode, set the level of analog interface, read devices settings, and easy to maintain -Automatic online test function can realize level test and signaling test for analog interface, functional test for data interface, functional tests of A/B ground, short circuit for external lines, very convenient to locate fault quickly and correctly |
High Reliability
| -Master (MST) cards and power supply cards adopt hot redundant backup -Advanced circuit design, modular structure -Adopting low power consumption, high reliable components -All functional cards support hot swap. |
Smart Shelf
| -3U high, 19 standard shelf -Compact, beautiful, light and good strength design |
Low Power Consumption
| -The power consumption is less than 30 Watt |
DI (drop/insert) function | The DI function is performed by software, to meet the needs of different types of users via flexible configuration of monitoring system |
basic Boards | |
MST board | FT-50S (3U) PCM Equipment has two Master cards (one master card mode can be selected), they perform non-blocking time slot cross connection between 2048×2048 slots. The master card mainly consists of one CPU unit, time slot interconnection unit and channel testing unit |
ring supply card | The ring supply card generator ring for FXS, HOT, CRR and MAG cards. |
PWR board | -48V DC or 220V AC is optional, supports dual power supply |
Common Cards | |
Audio Service sub-channel cards | -FXO card: provides 4 channels FXO interface -FXS card: provides 4 channels FXS interface - 4-wire E&M audio card: provides 4 channels 4-wire E/M interface, supports E/M signaling. -Magneto interface card: provides 4 channels magneto interface. -Carrier wave magneto card: to connect with a single magneto set or magneto attendant console. -Hotline telephone card: provides 4 hotlines
|
Data Service Sub-channel card | -Co-directional data card: contains 4 channels, conforms to ITU-T G.703 standard -RS232 data card: contains 4 channels asynchronous RS232 data interface, conforms to ITU-T V.24/V.28 standard -RS485 data card: contains 4 channels asynchronous RS485 data interfaces, they are full duplex and four wire mode interfaces -N×64Kbps FV.35 card: contains 1 channel synchronous V.35 data of N×64Kbps data rate, N is from 1 to 30 -10/100M Ethernet data interface card: providing 4 channel 10/100 Base-T Ethernet bridge, support VLAN -4E1 interface card: 4 E1 interfaces, 75Ω or 120Ω is optional -4E1 PDH interface card: access 4 E1s |
Common Cards
One channel card can hold two different sub-channel cards to compose different functional access cards-channel cards, data sub-channel cards and optical sub-channel cards.
Specifications
* Optical Fiber Interface
-Port number: 1-2, support redundant backup
-Bit rate: 150Mbps+/-50ppm
-Wavelength: 1310nm/1550nm
-Optical power:>-9dBm
- Sensitivity:<-38dBm (BER≤1*10-10)
-Distance: 0 - 120Km
-Connector: FC/PC
*E1 Port
-Port number: 64
-Bit rate: 2.048Mbps (50ppm)
- Impedance: 75ohm or 120ohm
-Line Code: HDB3, compliance with ITU-T G.703
-Jitter: compliance with G.823
* Ethernet Port
-Port number: 4, optional
-Speed: 10/100Mbps line speed
-Duplex: Half duplex/Full duplex self adaptation
-Frame Size: 64 - 1536 bytes
-Connector: RJ45
*Environmental Requirements
-Power supply: -48 VDC +-15%
-Fully equipment power consumption: 50W+-10%
-Operating temperature: 0ºC~45ºC
-Humidity: < = 95% (free from condensing)
-Atmospheric pressure: 70~106 Kappa
-Storage temperature: -40ºC ~70 ºC
*Mechanical dimensions
-Dimensions: 482 (L) x 240 (W) x 192 (H) mm
-Weight: 8Kg.