dimmable led driver 100w
1)High Efficiency (up to 91%)
2)Build-in Active PFC (Typical 0.98)
3)Wide Input Voltage90-305Vac
constant current dimmable led driver 100w
SHC100 SERIES SPECIFICATIONS
Model | Output Current (±5%) (mA) | Output Voltage (V) | Efficiency | No Load Output Voltage (V) | Ripple & Noise (V) | |
110V input | 220V input | |||||
SHC100-0350SW | 350 | 172 ~ 286 | 93.0% | 94.0% | 300 | 3% Vo |
SHC100-0450SW | 450 | 132 ~ 222 | 91.0% | 92.0% | 233 | 3% Vo |
SHC100-0700SW | 700 | 86 ~ 143 | 88% | 89% | 150 | 3% Vo |
SHC100-1050SW | 1050 | 57~95 | 88% | 89% | 101 | 3% Vo |
SHC100-1400SW | 1400 | 43~71 | 88% | 89% | 75 | 3% Vo |
SHC100-1750SW | 1750 | 34~57 | 88% | 89% | 63 | 3% Vo |
SHC100-2100SW | 2100 | 29~48 | 88% | 89% | 52 | 3% Vo |
SHC100-3150SW | 3150 | 19 ~ 32 V | 88% | 90% | 35 | 3% Vo |
NOTE: 1. All specifications are typical at 25°C unless otherwise stated.
2. The “Efficiency” values are measured at full load, after the unit is thermally stabilized, otherwise they will be lower about 1%
3. The “Ripple & Noise” values are measured by 20MHz bandwidth oscilloscope and the output paralleled a 0.1uF ceramic capacitor and a 10uF electrolytic capacitor.
ELECTRICAL SPECIFICATIONS
| Parameter | Values | Conditions |
INPUT | AC Voltage | 90 ~ 305 Vac | Operating Voltage |
Frequency Range | 47 ~ 63 Hz |
| |
PF(110V input) | 0.99 | Full load, Vin=110V | |
PF(220V input) | 0.96 | Full load, Vin=220V | |
AC Current (110V input) | 1.3 A | Full load, Vin=110V | |
AC Current (220V input) | 0.6 A | Full load, Vin=220V | |
Inrush Current | 65 A | Cold start, Vin=230V | |
Leakage Current | 1 mA | Vin=277V, 50Hz | |
OUTPUT | Top Output Power | 100 W |
|
Set-up Delay Time | 0.9 ~ 1.0 s |
| |
Line Regulation | 1% |
| |
Load Regulation | 5% |
| |
DIMMING | 10V Output Voltage | 10~11 V |
|
10V Output Source Current | 0~10 mA |
| |
Absolute Max. Voltage | 0~12 V | On the 1-10V input pin | |
Source Current | 0~10 mA | ||
PROTECT | Over Voltage Protect | 1.25 Vo | ±5% floating deviation |
Latch mode.The power supply shall return to normal operation only after the power is turn-on again. | |||
Short Circuit Protect | No damage shall occur when any output operating in a short circuit condition. The power supply shall be self-recovery when the fault condition is removed. | ||
Over Temperation Protect | 110°C |
|
NOTE: 1. All specifications except “OTP” are measured at 25°C .
2. The dimming fuction can be achieved by two modes. One is connected with a potentiometer, and the other is an input signal of 1-10Vdc.
PRODUCTS INFORMATION