1:Display on the wall or tilt display counter
2:Mobile phone Security display holder with alarm function
3:Color:Black / white
Product Name: Alarm security display stand
Product Information:
This elegant Alarm security display stand for cell phone/mobile , high practical, the use of UV surface treatment technology, which greatly promoted the launching of experiential marketing have to promote improvement in performance and product security
Now widely used in various types of mobile phones, cameras, MP4 and other Consumer Electronics products for Mobile phone supermarkets, used for loss prevention security of telecom mobile Unicom, digital city, digital camera counters, GPS counters, MP4 counters, appliances hypermarkets, supermarkets and various small electronic products exhibition of digital
It’s Upgrade the marketing model from the traditional "tell-style" to the innovative "experiential",consumers select products and convenient services from the staff "recommended style" which facilitate the consumers while improving business performance.
Alarm security display stand for cell phone/mobile are composed of the host alarm system, multi-touch alarm sensor, 3M adhesive and other components. Simple installation methods, such as installation of alarm installed in display racks or display case, Sensor (alarm probe) adhere to the product
Technical parameter
1.Product Height: 100 * 65 * 145MM
2.Internal Battery type: 3.7V rechargeable lithium battery.
3.External power adapter: DC5V 1000MA
4.Battery Standby Time: 2 months
5 Charge indicator: charging in red , full in green
6.Alarm sound: 105DB.
7) Alarm indication: LED red flashes.
8) Shell Material: ABS
9) Shell Color: bright black , pearl white
Function:
1) Host Base with Charging Function, Charging monthly , Repeated use.
2)Display Charging Function apply to : Mobile Phone , DC camera , Tablet PC
3)Disconnection Alarm Function: Three Contacts disconnection alarm
4)Low Voltage Alarm Function :Voltage Less 3.3V Alarm ,remind the charging
5)Short Circuit Alarm Function : circuit is short-circuited ,automatic alarm
6)Infrared Remote Control Function : Remote Start and Disarm the Alarm.
7)Installation Method : Double ways in 3mm adhesive or use screws tighten.
Products installation
1.Clean the display case, then turn on switch on the bottom of Alarm security display stand for cell phone/mobile host, adhere the bottom of the anti-theft frame with 3M adhesive tape to the exhibit cabinet. Or use two anti-theft screws to connect the cabinet frame and tighten the exhibition (open f the screw hole cover firstly)
2.Connect the charger of Alarm security display stand for cell phone/mobile with the alarm host, the other end into the power socket in preparation for a fixed monthly charge.
3.Tear off the 3 adhesive tape from the Anti-Theft Terminal product display and paste exhibit’s back fastened
4.Tear off 3M adhesive from the sensor probe, stick tight with the obverse of the product
5.Take out the Infrared remote control board , tear off the battery insulation sheet underneath. Press the ON key , the host switch on ,enter the preset alarm status
6.The installation is set up
Products list
1 .Alarm security display stand for cell phone/mobile host base (with a rechargeable lithium battery inside) 1 pcs.
2, Aalarm sensor probe(with a magnetic back, paste 3M adhesive. Extension cords ) 1 set
3, Charger and USB charging cable 1 set
4, Cell phone charging adapter cable 1 pcs
5, Remote control 1 pcs
6 Operation Manual 1pcs
7 Additional 3M adhesive and screws 1 set
7. FAQ and solutions about Alarm security display stand for cell phone/mobile
Symptom
| Solution
|
1 Turn on the remote control switch, the host no respnse.
| 1.Check the hidden switch on the bottom if in turned on status; 2.Check the host base if out of power , please charge when it’s run out .
|
Alarm is “beep” continuous | Charge for the Alarm security display stand for cell phone/mobile |
Turn the Announciator , alarm immediately with flashing red LED lights..
| 1, check whether the host seat adpress the counter display 2, check whether RJ plug of the sensor has inserted into the RJ socket behind the host seat the correctly 3, check whether the sensor and displays well-connected, if the adhesive on the sensor and displays have been tripping off, replace the 3M adhesive 4, check whether the small sensor contacts with the exhibit surface well .
|
Alarm security display stand
