Welcome to B2BAGE
new high end door & window hardware.jpg
new high end door & window hardware.jpg

Minimum Order: 0
Quality/Safety Certification: 0.00


1.OEM service is available
2.ISO 9001:2000 and CE certified
3.Small MOQ
4.25 - 300MT progressive punching machine

Specifications

1.Investment casting.precision casting
2.carbon steel/alloy steel/stainlee steel/aluminum
3.ODM/OEM
4.FIMA APQP QA QC,AQL,R&D

 

The ultimate success of the casting design depends on the communication between the designer and foundry engineers. When the foundry is properly informed of part requirements, there is usually a compromise of specifications that will allow for maximum compliance to print specifications and finish part design.

1 Standard Linear Tolerance(mm)
As-cast tolerances of angles is mainly a function of the part design and their ocation in casting. They range from +/- 1/2 degree (considered minimum) for well supported positions to +/- 2 degree where existing distortion could be expected. Inclusion of gussets and ribs normally minimizes distortion and many sections can be mechanically straightened.
3 Flatness, Strengteness and Roundness

Section Thickness

Possible Thickness Section Sink per Face of Casting

Normal

Premium

Up to 25

0.20

0.10

25 to 50

0.40

0.20

50 to 100

0.60

0.30

100 to 150

0.80

0.40

Straightening adds cost, but sometimes cannot be avoided. The actual straightening costs are often dependent on the tightness of the tolerance specified, so do not specify tighter flatness, straightness, roundness, or other requirements than you actually require. (WOTECH typically straightens parts using die sets that will be included in your tooling price.)
4 Size and Weight Range
Size and Weight. Part size and weight are the most critical factors in determining part cost because mold capacity is limited by both size and weight. The more pieces that can run on a mold, the lower the part cost. Unnecessary mass should always be removed by correct engineering practices to reduce part weight.

Items

Size

Premium

Outline Dimention

1000×620×380

up to 100

Weight(kgs)

0.001-60

0.10 to 1.50

Min. Wall Thickness

0.50

5 to 10

5 Surface Roughness
80 to 120 RMS are average.
6 Hole Length
Making a good hole in a casting is dependent on the integrity of the shell. The ratio of holediameter to length is important in determining what can be offered. Blind holes must have aradius at the top and the bottom of the hole to insure that a strong core is built for castingpurposes and to insure the best possible casting.


7.When possible, parts should be designed so that a single gate can feed the part. This will generally yield more pieces per mold and reduce the pour weight per mold.
We build gate grind fixtures for virtually all parts produced that require gate grind. When possible, the part should be designed so the gate can be put on flat surface rather than curved surface. Gate grind tolerances are listed from least to greatest cost.
1. Break-off witness (same alloys)
2. 0.20-0.50mm high witness
3. Flush grind
8 Heat Treatment
Heat treatments are used to control hardness, mechanical properties, corrosion resistance, and surface treatments. Unless otherwise indicated, all alloy steels are quoted with a normalize or anneal. All 300 series stainless steels and 17-4PH are quoted with a solution anneal.
9 Certification
Chemical Certification can be provided at no extra cost. Mechanical Property Certification adds to cost, so it's best to consider a combination of Chemistry and Hardness Certification instead. Marking each casting with heat number also adds to the cost. Investment casting in lot numbers may be a good tracability option for commercial parts.

1.OEM service

2.National standard steel and Japanese standard of high precision

3.ISO 9001:2000 and CE certificated

 

Ads by Google



About Us | Contact Us | Help | Terms & Conditions
Hot Products: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 0-9
Copyright Notice @ 2008-2022 B2BAGE Limited and/or its subsidiaries and licensors. All rights reserved.