1.ip68 blue led boat light
2.Power :6X3W
3.Working Voltage:DC8-28V
4.Waterproof :IP68
5.Color:R/G/B/Y/W
cree 18w ip68 blue led boat light for navigation
Spec.
Part No. | Power (W) | Emitting Color | Wavelength (nm) | Working Voltage (V) | IP Grade | Luminous Flux (Lm) | Emitting Angle of Peak (θ) | gross weight |
SHTDF01-6X3R | 6X3W | Red | 630 | DC8-28V | IP 68 | 400-430 | 30 | 1.5kg |
SH -TDF01-6X3G | 6X3W | Green | 520 | 600-660 | 1.5kg | |||
SH -TDF01-6X3B | 6X3W | Blue | 460 | 120-140 | 1.5kg | |||
SH-TDF01-6X3Y | 6X3W | Yellow | 590 | 400-430 | 1.5kg | |||
SH-TDF01-6X3W | 6X3W | White | / | 720-760 | 1.5kg |
Powerful LED Underwater light made with high quality Marine grade stainless steel 316 housing. This light adds ambiance to your boat and, for the fishermen, attracts fish.
SH-TDF01-6X3 LIGHTING INSTALLATION INSTRUCTION
WARNINGS!!!!
LIGHTS ARE FOR UNDERWATER TRANSOM USE ONLY!!!!!
POWER REGULATOR MUST BE USED ON ALL 6X3 LIGHTS.
AN UNDERWATER MARINE SEALANT REQUIRED AND 316 S/S screws to be used.
PROFESSIONAL INSTALLATION IS RECOMMENDED.
3 AMP FUSE MUST BE USED FOR ALL 6X3 LIGHTS.
WARRANTY WILL BE VOID IF FUSE NOT USED.
3 YEAR WARRANTY FROM DATE OF PURCHASE, REPAIR OR REPLACEMENT OF LIGHT.
VERIFY ALL DIMENSIONS BEFORE DRILLING ANY HOLES IN THE BOAT.
6X3 Light Installation :
The 6X3 Light can be installed in two different ways:
Flush Mount with the wire through the Transom
1. Look inside the boat making sure the area you want to mount the light is Free and Clear and accessible.
2. You want to mount the lights to the Transom leaving at least two inches between the light and the bottom of the boat.
3. Make a template, follow the plate and drill a pilot hole into the Transom approximately 3/16 inch to prevent cracking of the Gel Coat.
4. For the center hole, use a 3/4 inch Drill Bit and drill approximately 3/16 inch into the Gel Coat to make a good space for sealant.
5. Use a 3/16 inch Drill Bit and drill the center of the 3/4 inch hole through the transom.
6. The Center hole gets approximately 1/4 inch bead of sealant, enough to fill the 3/4 inch hole you drilled in step 4.
7. Slowly push the wire through the Transom and hold the light still while installing the 4 supplied screws, with approved sealant.
8. Go inside the boat to the area the wire comes through and seal the inside of the Transom with sealant as well.
9. To hook up the lights to power you must find a power source for the 6X3 Light. You can use 10V~30V DC Neg- ground.
Flush Mount with Spacer --the wire is secured to the Transom entering the boat above the water line using a clam shell or an already existing hole.
1. Mount lights on the Transom with a Spacer requires a minimum of 2 inches between the bottom of the boat and the light.
2. Locate the mounting location using a Template and drill three pilot holes approximately 1/4 inch into the Gel Coat.
3. Using a Marine Underwater Sealant, place a small amount onto the Gel Coat.
4. Run the wire up the Transom and enter the boat through an existing “Clam Shell” or drill a 3/16 inch hole above the water line. Using a Sealant to seal the cable and use a “Clam Shell”to cover the wire.
5. Hook up electric to the Lights the same as in steps for installation above.
6X3 LIGHTS MUST BE USED WITH THE POWER REGULATOR. IF REGUALTOR ENCLOSED IS NOT USED YOU WILL DAMAGE THE LIGHT AND THE WARRANTY WILL BE VOID.
(See the below connection sketch.)