Gps tracking spy /vehicle tracker system support camera
1.two ways communciation
2.support gprs data transmissio
Gps tracking spy /vehicle tracker system support camera
1 Summary
Working based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any remote targets by SMS or GPRS,and guard against theft of Vehicle.
2 Applications
l Rental vehicle / Fleet management etc
l Covert Tracking
3 Hardware Description
3.1 Wires Connection
1 SP – Connects the round speaker (connection is ready ,only need connect the speaker)
2.SP + Connects the round speaker (connection is ready ,only need connect the speaker)
3. MIC + microphone +(connection is ready)
4. MIC + microphone -(connection is ready)
5. GND SOS Ground (connection is ready)
6. SOS SOS +(connection is ready)
7. Oil test (analog input port )connects the black wire for the fuel sensor. Note: Please use our fuel sensor only.
8. ACC (digital input port) connect the ACC (ignition)
9. V + connects relay, connction is ready,conencts the relay,it works.
10. Output (digital output) Connects the extra relays
11. Temperature test (analog input port) connects the middle connector of the round temperature sensor.
12. Cut oil (digital output) connects the relay, connction is reay,conencts it,it works.
13. Out A (digital output) for the extra relay.
14. Out B (digital output) for the extra relay.
15. IO6 in (digital input port) connects the detective circuit of the switches for the doors and tail in the car.
16. IO5 in(digital input port) connects the detective circuit of the switches for the doors and tail in the car.
17. IO4 in (digital input port) connects the detective circuit of the switches for the doors and tail in the car.
18. IO3 in (digital input port) connects the detective circuit of the switches for the doors and tail in the car
19. IO2 in (digital input port) connects the detective circuit of the switches for the doors and tail in the ca
20. IO1 in (digital input port) connects the detective circuit of the switches for the doors and tail in the ca
Note: Two UART with the connectors of A.B C D; E F G H for 2 purposes.
Connect the extra cameraFor input/output the dataConnects any conenctors ABCD or EFGH optionally, function actived.
UART1 (al-qeada ND B.R X cristiano TX d. + 5V)
UART 2 (um participant G.T X X F.R ND h. + 5V)
3.2 Interior
3.3 Relays connection
4 Specs
Content | Specs. |
Dimension. | 8.2x8.2x2.8cm |
Weight | 195g |
Network | GSM/GPRS |
Band | 850/1800/1900Mhz or 900/1800/1900Mhz |
GPS chip | SIRF3 chip |
GPS sensitivity | -159dBm |
GPS accuracy | 5m |
Time To First Fix | Reacquisition 0.1s Cold status 45s Warm status 35s Hot status 1s |
Power | 9—36V input |
Battery | Chargeable changeable 3.7V 1100mAh Li-ion battery |
Standby | 50hous |
Storage Temp. | -40°C to +85°C |
Operation Temp. | -20°C to +55°C |
Humidity | 5%--95% non-condensing |
5 Battery and SIM card installation
Make sure that there is no call transfer and call display is on, and PIN code off. The SMS message must in Text format, can’t be identified for PDU format.
Steps:
1.Open the rear cover, insert a SIM card to the simcard slot A. (If using one simcard,do not insert it into simcard slot A since the default simcard is simcard B)
2.Insert the SD card
3.Use a stick or pick up the simcard slot B,insert the simcard.