Led Driver
High Efficiency (up to 91%)
Build-in Active PFC (Typical 0.98)
Waterproof (IP67)
OVP, SCP, OTP
LED Driver SHC40 SERIES SPECIFICATIONS
Model | Output Current (±5%) (mA) | Output Voltage (V) | Efficiency | No Load Output Voltage (V) | Ripple & Noise (V) | |
110V input | 220V input | |||||
SHC040-0350SW | 350 | 69~114 | 89.0% | 91.0% | 127 | 4.5 |
SHC040-0450SW | 450 | 54~89 | 89.0% | 91.0% | 98 | 3.5 |
SHC040-0700SW | 700 | 35~57 | 88.0% | 90.0% | 61 | 2.2 |
SHC040-1050SW | 1050 | 12~36 | 86% | 87% | 41 | 5 |
SHC040-1280SW | 1280 | 10~29 | 86% | 87% | 35 | 3 |
SHC040-1400SW | 1400 | 10~25 | 86% | 87% | 35 | 3 |
SHC040-1660SW | 1660 | 8~23 | 85% | 86% | 30 | 3 |
NOTE: 1. All specifications are typical at 25°C unless otherwise stated.
2. The “Efficiency” values are measured at full load, after the unit is thermally stabilized, otherwise they will be lower about 1%
3. The “Ripple & Noise” values are measured by 20MHz bandwidth oscilloscope and the output paralleled a 0.1uF ceramic capacitor and a 10uF electrolytic capacitor.
Led Driver ELECTRICAL SPECIFICATIONS
| Parameter | Values | Conditions |
INPUT | AC Voltage | 90 ~ 305 Vac | Operating Voltage |
Frequency Range | 47 ~ 63 Hz |
| |
PF(110V input) | 0.98 | Full load, Vin=110V | |
PF(220V input) | 0.92 | Full load, Vin=220V | |
AC Current (110V input) | 0.53 A | Full load, Vin=110V | |
AC Current (220V input) | 0.30 A | Full load, Vin=220V | |
Inrush Current | 20 A | Cold start, Vin=230V | |
Leakage Current | 0.5 mA | Vin=277V, 50Hz | |
OUTPUT | Top Output Power | 40 W |
|
Set-up Delay Time | 1.5 ~ 3.0 s |
| |
Line Regulation | 2% |
| |
Load Regulation | 3% |
| |
Source Current | 0~10 mA |
| |
PROTECT | Over Voltage Protect | 1.25 Vo | ±5% floating deviation |
Latch mode.The power supply shall return to normal operation only after the power is turn-on again. | |||
Short Circuit Protect | No damage shall occur when any output operating in a short circuit condition. The power supply shall be self-recovery when the fault condition is removed. | ||
Over Temperation Protect | 110°C |
|
NOTE: 1. All specifications except “OTP” are measured at 25°C .
Led Driver SAFETY & EMC COMPLIANCE
Parameter | Standards |
Safety UL/c-UL, CE | UL8750, UL935, UL1012, UL1310 Class2, CSA-22.2 No.107.1, CSA-C22.2 NO.223-M91 Class2 EN61347-1, EN61347-2-13 |
EMI | EN55015, FCC Part 15 Class B, ANSI C63.4: 2009 |
EMS | EN61000-3-2, EN61000-3-3, EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11, EN61547 |
ENERGY STAR | ANSI/IEEE C63.41-1991 |