Toshiba TB6560AHQ chip. step angle 1.8. Holding torque 18.9kgf.cm; Overload, over-current and over-temperature safety .24V power
CNC controller kit 3 Axis Stepper Driver Controller + NEMA 23 Step Motor *3 + 24V Power Supply
sku:UC065
Features of Stepper Driver :
Toshiba TB6560AHQ chip - High power, maximum 3.5A drive current chipset !
1-1/16 microstep setting - Higher accuracy and smoother operation than standard 1, 1/2 step!
Adjustable 1.5A-3A drive current settings for each axis - 25%,50%,75%,100% of full current can be set for different stepper motors
Overload, over-current and over-temperature safety - Full protection for your computer and peripheral equipment !
On board current switching - Power output can be set according to specific user requirement !
Full closed-type optical isolation to protect the user's computer and equipment
Relay spindle interface - Outputs Max. 36V 7.5A for spindle motors or coolant pump (only one device can be powered by this output!)
4 channel inputs interface- Can be used for XYZ limit and emergency stop !
Professional design - Two stage signal processing with super anti-jamming !
Bipolar constant current chopper drive with non-resonant region - Controls motors smoothly through range without creep effect !
Four control inputs (divided into pairs of knives) - Allows setting of limit and emergency stop !
Universal architecture - Supports most parallel software MACH3,KCAM4 etc!
Attention:Please connect the power supply to the power switch of 12-36 V, 8A The power output of 12V shall be applied to the radiator fan of 12V The interface of driver shall be connected with 2/4 phase, 4/6/8 leads stepper motor within 3A current This board can work with both unipolar and bipolar stepper motors The spindle motor is controlled by Parallel Interface. The voltage of the spindle motor must comply with the scope of the supply voltage.
Specifications of Driver
Electrical properties (ambient temperature Tj = 25 pm) | |
Input Power | 12 - 36V DC power supply |
Stepper motor drive current | 3A (peak value 3.5A)/axis |
Drive type | Double-pole constant flow PWM actuation output |
Compatible Stepper motors | 2/4 Phase, 4/6/8 leads stepper motors within 3.5A |
Specification of 57BYGH76-401A Motor:
Step Angle Accuracy: +-5%(full step, no load) Resistance Accuracy: +-10% Inductance Accuracy: +-20% Temperature Rise: 80 Celsius CMax.(ratod current,2 phase on) Ambient Temperature: -10Celsius +50Celsius Insulation Class: B Dielectric Strength: 500V AC for one minute Shaft Radial Play: 0.06Max.(450g-load) Shaft Axial Play: 0.08Max.(450 9-load)
24V 240W Power Supply:
| DC VOLTAGE | 24V |
| RATED CURRENT | 10A |
| CURRENT RANGE | 0 ~ 10A |
| RATED POWER | 240W |
| VOLTAGE ADJ. RANGE | 20 ~ 28V |
Features:
Auto switched 88 ~ 264VAC input Built-in passive PFC choke Protections: Short circuit / Overload / Over voltage / Over temperature Forced air cooling by built-in DC fan Built-in cooling Fan ON-OFF control LED indicator for power on Fixed switching frequency at 75KHz
AC input range selectable by switch
Protections: Short circuit/ Overload Cooling by free air convection 100% full load burn-in test Low cost, hogh reliabilityPackage included:1 x 3 Axis TB6560 Stepper Motor Driver 3 x Nema 23 57BYGH76-401A Stepper Motor 5 x Wire connectors 1 x Cable 1 x CD software(English Manual & Mach 3) 1 X 24V 240W Power Supply
