Dimmable Led Driver
1)High Efficiency (up to 92%)
2) Build-in Active PFC (Typical 0.99)
3)Constant Output Current
SHC120 SERIES SPECIFICATIONS
Model | Output Current (±5%) (mA) | Output Voltage (V) | Efficiency | No Load Output Voltage (V) | Ripple & Noise (V) | |
110V input | 220V input | |||||
dimmable led driver SHC120-0350SW | 350 | 206 ~ 343 | 90% | 92% | 350 | 3% Vo |
dimmable led driver SHC120-0450SW | 450 | 160 ~ 267 | 90% | 92% | 275 | 3% Vo |
dimmable led driver SHC120-0700SW | 700 | 103 ~ 171 | 90% | 92% | 180 | 3% Vo |
Dimmable led driver SHC120-1050SW | 1050 | 68 ~ 114 | 89% | 91% | 120 | 3% Vo |
dimmable led driver SHC120-1400SW | 1400 | 52 ~ 86 | 89% | 91% | 90 | 3% Vo |
dimmable led driver SHC120-1750SW | 1750 | 41 ~ 68 | 89% | 91% | 70 | 3% Vo |
dimmable led driver SHC120-2100SW | 2100 | 34 ~ 57 | 89% | 91% | 60 | 3% Vo |
dimmable led driver SHC120-2800SW | 2800 | 26 ~ 43 | 89% | 91% | 45 | 3% Vo |
NOTE: 1. All specifications are typical at 25°C unless otherwise stated.
2. The “Efficiency” values are measured at full load, after the unit is thermally stabilized, otherwise they will be lower about 1%
3. The “Ripple & Noise” values are measured by 20MHz bandwidth oscilloscope and the output paralleled a 0.1uF ceramic capacitor and a 10uF electrolytic capacitor.
dimmable led driver ELECTRICAL SPECIFICATIONS
| Parameter | Values | Conditions |
INPUT | AC Voltage | 90 ~ 305 Vac | Operating Voltage |
Frequency Range | 47 ~ 63 Hz |
| |
PF(110V input) | 0.99 | Full load, Vin=110V | |
PF(220V input) | 0.96 | Full load, Vin=220V | |
AC Current (110V input) | 1.5 A | Full load, Vin=110V | |
AC Current (220V input) | 0.7 A | Full load, Vin=220V | |
Inrush Current | 65 A | Cold start, Vin=230V | |
Leakage Current | 1 mA | Vin=277V, 50Hz | |
OUTPUT | Top Output Power | 120 W |
|
Set-up Delay Time | 0.8 ~ 1.2 s |
| |
Line Regulation | 1% |
| |
Load Regulation | 5% |
| |
DIMMING | 10V Output Voltage | 10~11 V |
|
10V Output Source Current | 0~10 mA |
| |
Absolute Max. Voltage | 0~12 V | On the 1-10V input pin | |
Source Current | 0~10 mA | ||
PROTECT | Over Voltage Protect | 1.25 Vo | ±5% floating deviation |
Latch mode.The power supply shall return to normal operation only after the power is turn-on again. | |||
Short Circuit Protect | No damage shall occur when any output operating in a short circuit condition. The power supply shall be self-recovery when the fault condition is removed. |