LED Driver 40W
1)LED Driver high Efficiency (up to 91%)
2)Build-in Active PFC (Typical 0.98)
3)Constant Output Current
led driver 40W
SLD040 SERIES SPECIFICATIONS
Model | Output Current (±5%) (mA) | Output Voltage (V) | Efficiency | No Load Output Voltage (V) | Ripple & Noise (V) | |
110V input | 220V input | |||||
SLD040-0350SW | 350 | 69~114 | 89.0% | 91.0% | 127 | 4.5 |
SLD040-0450SW | 450 | 54~89 | 89.0% | 91.0% | 98 | 3.5 |
SLD040-0700SW | 700 | 35~57 | 88.0% | 90.0% | 61 | 2.2 |
SLD040-1050SW | 1050 | 12~36 | 86% | 87% | 41 | 5 |
SLD040-1280SW | 1280 | 10~29 | 86% | 87% | 35 | 3 |
SLD040-1400SW | 1400 | 10~25 | 86% | 87% | 35 | 3 |
SLD040-1660SW | 1660 | 8~23 | 85% | 86% | 30 | 3 |
NOTE: 1. All specifications are typical at 25°C unless otherwise stated.
2. The “Efficiency” values are measured at full load, after the unit is thermally stabilized, otherwise they will be lower about 1%
3. The “Ripple & Noise” values are measured by 20MHz bandwidth oscilloscope and the output paralleled a 0.1uF ceramic capacitor and a 10uF electrolytic capacitor.
ELECTRICAL SPECIFICATIONS
| Parameter | Values | Conditions |
INPUT | AC Voltage | 90 ~ 305 Vac | Operating Voltage |
Frequency Range | 47 ~ 63 Hz |
| |
PF(110V input) | 0.99 | Full load, Vin=110V | |
PF(220V input) | 0.96 | Full load, Vin=220V | |
AC Current (110V input) | 0.53 A | Full load, Vin=110V | |
AC Current (220V input) | 0.30 A | Full load, Vin=220V | |
Inrush Current | 20 A | Cold start, Vin=230V | |
Leakage Current | 0.5 mA | Vin=277V, 50Hz | |
OUTPUT | Top Output Power | 40 W |
|
Set-up Delay Time | 1.5 ~ 3.0 s |
| |
Line Regulation | 2% |
| |
Load Regulation | 3% |
| |
DIMMING | 10V Output Voltage | 10~11 V |
|
10V Output Source Current | 0~10 mA |
| |
Absolute Max. Voltage | 0~12 V | On the 1-10V input pin | |
Source Current | 0~10 mA | ||
PROTECT | Over Voltage Protect | 1.25 Vo | ±5% floating deviation |
Latch mode.The power supply shall return to normal operation only after the power is turn-on again. | |||
Short Circuit Protect | No damage shall occur when any output operating in a short circuit condition. The power supply shall be self-recovery when the fault condition is removed. | ||
Over Temperation Protect | 110°C |
|
PRODUCTS INFORMATION
Parameter | Values |
Working Temp., Humidity | -20°C ~ +60°C; 10 ~ 100% RH non-condensing |
Storage Temp., Humidity | -40°C ~ +85°C; 5 ~ 100% RH |
MTBF | 470,000 hours |
Life Time | 85,000 hours |
Dimension | Inches (L*W*H) 3.74*2.76*1.26 |
Milimeters (L*W*H) 95*70*32 | |
Net Weight | 330g |